Replace the TS68C429A at End of Life with the M68C429A ARINC 429 IP

Replace the TS68C429A at End of Life with the M68C429A ARINC 429 IP

The TS68C429A ARINC 429 controller has reached end of life: Teledyne e2v set its last-time buy for 3 May 2023 and its last shipment for 3 May 2024, with no fit, form and function replacement planned. For a board that still has years of service ahead, one route is to move the controller function into an FPGA with the M68C429A ARINC 429 IP from Logic Design Solutions. This guide sets out what that IP does, what it does not do, and what a migration really involves.

The short answer

The TS68C429A is past its last-shipment date (3 May 2024), and Teledyne e2v plans no fit, form and function replacement. The M68C429A is a VHDL macro, based on the TS68C429A, that moves the ARINC 429 controller function into an FPGA; the macro provides 8 receivers, 3 transmitters with FIFO and a 68000-type CPU interface on a 16-bit data bus. It is not strictly compatible with the TS68C429A, so plan a small design project rather than a part swap: check the register map and software behaviour, assign the pinout in the FPGA, rerun the delivered testbench, then requalify according to your programme. Logic Design Solutions can adapt the CPU interface and customise the macro where your board needs it.

TS68C429A end of life: what the notice says

Teledyne e2v announced the end of life of its TS68C429 series of ARINC 429 controllers in notice GE224251, dated 4 November 2022. The notice covers five part numbers: TS68C429AVFB, TS68C429AMFB, TS68C429AMFBCB, TS68C429AVRB and TS68C429AMRB.

  • Last-time buy: 3 May 2023.
  • Last shipment: 3 May 2024.
  • Reasons given: falling manufacturing volumes, rising support costs and a production line that had become difficult to maintain.
  • Successor: Teledyne e2v does not plan a fit, form and function replacement part.

Both dates have passed. A programme that did not stock enough parts at the last-time buy now has three options: find remaining inventory, redesign the board around a different controller, or keep the board and replace only the controller function. The third option is the one an FPGA IP addresses, and it is often the least disruptive for a board whose surrounding design, software and qualification file are already in place.

What the M68C429A takes over

The M68C429A is an ARINC 429 synchronous multichannel receiver and transmitter, written in VHDL and based on the TS68C429A. Its product brief (version 1.3) lists the following functions.

Function M68C429A
Channels 8 independent receivers, 3 independent transmitters with FIFO
CPU interface 68000-type microprocessor interface, 16-bit data bus; compatible with 16- or 32-bit processors and adaptable on request
ARINC 429 line interface “1” and “0” lines, RZ code
Data rates All ARINC 429 rates, and up to 2.5 Mbit/s
Labels and parity Multi-label; odd, even or no parity
Interrupts and registers Independent interrupt lines for receive and transmit, vectored interrupts, direct addressing of all registers
Clock Operating frequency depends on the speed grade of the target FPGA

Because the macro is based on the TS68C429A, the review of your existing driver starts from the TS68C429A model, with differences to check. The protocol itself does not change either: if you need a refresher on word format, labels and rates, our ARINC 429 protocol guide covers it, and we will not repeat it here.

“Not strictly compatible”: what that means for your board

The phrase comes from the M68C429A product brief itself, and we prefer to put it up front. It means the ARINC 429 controller function is taken over, but the FPGA is not a pin-for-pin substitute for the TS68C429A package, and the macro’s behaviour has to be checked against what your software actually relies on.

In practice, the differences sit in three places:

  • The package. The controller now lives inside an FPGA, with its own footprint, supplies and pin assignment, and the board design has to take the new device into account.
  • The register map and timing seen by software. Every register access, interrupt and status flag your driver uses has to be compared with the macro’s datasheet. Where your code depends on a behaviour the macro handles differently, either the driver changes or Logic Design Solutions can adapt the macro.
  • The qualification file. A new device on the board means a new verification and, depending on your programme, a requalification. The IP can shorten that work; it does not remove it.

This is why we describe the M68C429A as a replacement route, not a substitute part. Being clear about it early saves a programme from discovering the gap during integration.

Oscilloscope probes touch an FPGA board while an engineer checks a data interface on a test bench.

TS68C429A replacement: the migration, step by step

A TS68C429A replacement with the M68C429A follows four steps. Their order matters, because each one feeds the next.

  1. Compare the register map and the software behaviour. Take the TS68C429A driver your board runs today and check each access against the M68C429A datasheet: register addresses, bit fields, interrupt vectors, FIFO handling. List every difference and decide, for each one, whether the software changes or the macro does.
  2. Assign the pinout in the FPGA. Map the CPU bus, the interrupt lines and the ARINC 429 “1” and “0” lines to FPGA pins that suit your board layout. The product brief counts 62 I/Os if every signal of the macro is brought out of the device; a design that keeps some signals internal needs fewer.
  3. Rerun the delivered testbench. The macro ships with a VHDL testbench for behavioural simulation and post-layout (gate-level) simulation. Run it on your configuration, after any customisation, before the device goes on a board.
  4. Requalify according to your programme. Simulation results are evidence for the controller; system-level acceptance remains defined by your programme’s own rules, on the real board with real traffic.

Logic Design Solutions can take on part of this work: adapting the CPU interface to your processor, customising the macro, or integrating it with other functions in the same device.

Which FPGA to host the controller

For an obsolescence replacement, a small flash FPGA is in our view a sensible host, for example from the Microchip IGLOO family. Flash FPGAs are non-volatile, so they start up without an external configuration memory. IGLOO devices are also low-power 130 nm parts.

The only occupancy figure published for the M68C429A dates from its 2004 product brief, on an Actel ProASIC+ APA300: 65% of the core cells, depending on whether synthesis favours area or speed. Actel is now part of Microchip. We have not published a measured occupancy on IGLOO, so the right device size for your board is something we establish with you from your configuration, rather than a figure we would quote here. Logic Design Solutions can size the FPGA’s density and I/O count to your specification.

What Logic Design Solutions delivers

The M68C429A is purchased under a licence agreement. The delivery includes:

  • the VHDL source code of the macro;
  • a VHDL testbench for behavioural and post-layout (gate-level) simulation;
  • the datasheet;
  • a user guide covering simulation, synthesis and place and route;
  • a constraint file.

A bitstream with its datasheet is available as an option. Six months of email and phone support by Logic Design Solutions are included with the macro; that support does not cover modifications made by the user, and maintenance contracts are available beyond it. Because the VHDL source is delivered, the controller function is no longer tied to one purchased chip, which is precisely the dependency an end-of-life notice exposes.

Logic Design Solutions can also integrate the macro with other pre-designed functions in the same FPGA. On an ageing board, that can be a chance to absorb a second obsolete part or some surrounding glue logic into the same device.

EF4442 boards and new designs

The M68C429A is also an enhanced version of the EF4442 receiver. If your board carries an EF4442 rather than a TS68C429A, the closer match is the MEF4442A, based on the EF4442 in mode A (4 receivers, 1 transmitter, 8-bit CPU bus). When 4 receive channels are not enough, the M68C429A is the step up. Our guide to replacing the obsolete EF4442 with the MEF4442A covers that case.

For a new design that has no legacy register map to preserve, a replacement macro is not the right starting point. Our current ARINC 429 IP is built for that case, and our article on the ARINC 429 IP core for FPGA explains how it fits a modern design. For a recording application, see designing avionics data recorders on FPGA with ARINC 429 IP. If you are still choosing a bus, see our comparison of ARINC 429, ARINC 629 and MIL-STD-1553.

In summary

With its last shipment behind it, the TS68C429A has no fit, form and function successor planned by Teledyne e2v. The M68C429A moves the controller function into an FPGA, for example a small flash device, with 8 receive and 3 transmit channels and a 68000-type CPU interface, delivered as VHDL source with its testbench. Plan for a register and software review, a pinout in the FPGA, a testbench run and a requalification. Logic Design Solutions can adapt the macro and the CPU interface to keep that work as small as your board allows.

How we wrote this article

The M68C429A and MEF4442A facts come from the Logic Design Solutions product briefs, version 1.3. The occupancy figure is the one published in the 2004 brief, on an Actel ProASIC+ device; it has not been re-measured on current FPGA families. The end-of-life dates come from Teledyne e2v notice GE224251 of 4 November 2022. Where we give a recommendation, it is our opinion, and we write it as such.

This article gives technical criteria and our point of view. It does not replace a review of your own board and programme requirements.

It is published by Logic Design Solutions, which therefore has an interest in the subject.

Sources
  1. Teledyne e2v, end-of-life notice GE224251, TS68C429 series ARINC 429 controllers, 4 November 2022, cited by number and date; the notice PDF was not reachable online on 12 October 2026.
  2. Logic Design Solutions, M68C429A Product Brief, version 1.3, January 2004, and M68C429A product page.
  3. Logic Design Solutions, MEF4442A Product Brief, version 1.3, January 2003, and MEF4442A product page.
  4. Microchip, IGLOO Low Power Flash FPGAs with Flash*Freeze Technology, datasheet.