Integrating an NVMe IP on FPGA: Architecture and Constraints

Integrating an NVMe IP on FPGA: Architecture and Constraints

News : The cost of high-end SSDs has surged, pushing well-known brands to price their models beyond the reach of many users. Meanwhile, multimedia files continue to demand more storage space, exacerbating the challenge for those relying on limited capacity. This shift in the storage market highlights the growing importance of technologies like NVMe over PCIe, which may offer a path to balancing performance and affordability in an increasingly demanding digital landscape. (Tech Critter, 30 September 2026).

NVMe over PCIe on FPGA isn’t just about bandwidth: it’s about matching lane width to the FPGA’s hard IP blocks before the design even starts. PCIe 5.0 signals at 32 GT/s per lane in each direction. The choice isn’t theoretical: it dictates whether your design saturates the link or bottlenecks at the first queue.

The short answer

Integrating NVMe IP on FPGA requires aligning PCIe lane width with the FPGA’s hard IP resources and target throughput. PCIe Gen3/Gen4/Gen5 lanes deliver 8/16/32 Gbps per lane, but raw bandwidth is reduced by encoding overhead: Gen3 x16, for example, carries about 15.75 GB/s per direction after 128b/130b encoding. On Altera Agilex 7, the R-Tile provides PCIe 5.0 hard IP up to x16, as endpoint or root port, while Gen3 and Gen4 designs depend on the hard IP of the chosen device. For multi-NVMe deployments, PCIe switches route TLPs via aperture-based addressing, but Access Control Services (ACS) can add latency if enabled. Compliance testing at UNH-IOL plugfests helps verify interoperability, though it is not a certification requirement. The FastPath evaluation on a Zynq development board reports up to 71% lower latency and up to fivefold higher I/O performance against the baseline.

PCIe lane requirements for NVMe IP integration on FPGA

NVMe IP integration on FPGA demands matching PCIe lane width to bandwidth needs and available FPGA resources.

PCIe lane requirements depend on the generation’s per-lane bandwidth and the FPGA’s PCIe hard blocks. PCI-SIG specifies lane widths from x1 to x32, allowing designers to allocate lanes against the FPGA’s constraints. A Gen3 x16 link, for example, delivers 128 Gbps unidirectional: 16 GB/s, since each Gen3 lane carries 8 Gbps raw, as Electronic Design details. Gen4 doubles this to 16 Gbps per lane, Gen5 to 32 Gbps, but these are raw rates; application throughput will be lower after encoding overhead.

On Altera Agilex 7, the R-Tile PCIe controller supports up to a Gen5 x16 link in endpoint or root-port mode, as ServeTheHome reported at launch. A single NVMe SSD usually connects over an x4 link, so lane planning is about how many drives the hard IP must serve, not only about peak bandwidth. Server-grade motherboards offer up to 128 PCIe lanes and can struggle to meet connectivity requirements for workloads with multiple GPUs, as EE News Europe notes.

Choose lane width based on your FPGA’s resources and target throughput.

PCIe Generation Per-Lane Bandwidth (Gbps) x4 Link (Gbps) x8 Link (Gbps) x16 Link (Gbps)
Gen3 8 32 64 128
Gen4 16 64 128 256
Gen5 32 128 256 512

NVMe protocol stack layers and FPGA implementation constraints

The NVMe protocol stack on FPGA requires handling multiple layers, from PCIe physical signaling to NVMe command processing, each adding constraints.

The NVMe protocol stack is structured in distinct layers, each introducing specific implementation challenges on FPGA hardware. Viavi’s Xgig 5P8 analyzer platform provides protocol analysis for PCIe 5.0 traffic at all layers of the protocol stack, as reported by EE News Europe.

For FPGA-based NVMe hosts, the physical interface is just the starting point. PCIe lanes must align with target bandwidth, while the protocol stack itself consumes logic for packet assembly, queue management, and command processing. The Logic Design Solutions’ catalogue lists NVMe host IP cores. Each layer introduces latency and resource overhead, which must be carefully balanced against the FPGA’s available logic and memory blocks.

Key constraints include:

  • Queues and namespaces: the LDS NVMe host IP handles up to 16 I/O queues and 8 namespaces.
  • Buffering: the I/O-queue buffer is configurable from 32 KB to 1024 KB, so memory use follows the throughput the application needs.
  • Data interface: a CPU interface suits sequential access, a FIFO interface suits I/O-intensive streams, with 512 B or 4096 B sectors.

On any target device, resource use depends on these settings. The available IP cores are delivered as VHDL/Verilog source with C drivers: ask for utilisation figures for your target device and configuration before committing to a part. Our recommendation: prioritize modular design, allowing selective enablement of protocol layers based on the target application’s needs.

FPGA family compatibility with PCIe Gen4 and Gen5 NVMe IP cores

Gen5 NVMe needs a device with PCIe 5.0 hard IP, such as Altera Agilex 7 with R-Tile; Gen3 and Gen4 are available on a wider range of devices.

The interface width and clock seen by the NVMe host IP change with the device. The table lists the combinations documented in the LDS catalogue.

FPGA Family PCIe Gen Support IP Core Type Key Consideration
Altera Agilex 7 (R-Tile) Gen5 (hard IP, up to x16) NVMe host Avalon user interface
AMD Artix UltraScale+ Gen4 NVMe host AXI, 256-bit at 250 MHz
AMD Kintex UltraScale+ Gen3 NVMe host AXI, 256-bit at 125 MHz

When selecting an FPGA for NVMe IP, match the PCIe generation to your bandwidth needs: Gen5 where the device has PCIe 5.0 hard IP, Gen3 or Gen4 where the device and the drives make that sufficient. Logic Design Solutions’ catalogue lists the NVMe host and SAN IP cores for these families.

NVMe over PCIe vs. NVMe over Fabrics: FPGA-specific trade-offs

Excelero reported in 2018 that NVMe over RoCE adds about 5µs to the roughly 100µs a direct-attached PCIe SSD needs.

TCP/IP and Fibre Channel transports cost more: the same report gives a vendor estimate of 180 to 200µs for them, according to Blocks & Files. For FPGA-based storage, the choice of transport can decide whether a design meets real-time constraints or misses them.

PCIe’s point-to-point link avoids the encapsulation steps that Fabrics require, reducing both latency and FPGA resource usage. Fewer protocol layers mean more logic blocks remain available for user logic or additional NVMe queues.

Fabrics, however, enable shared storage across multiple hosts. When your design must scale beyond a single FPGA, RoCE or TCP/IP can connect multiple devices without sacrificing the NVMe protocol. The trade-off is clear: PCIe for speed, Fabrics for scale.

Connection Latency (µs) FPGA Resource Use Use Case
NVMe over PCIe ~100 Low Single-host, real-time
NVMe over Fabrics ~105 (RoCE, vendor figure) Higher Multi-host, scalable

Our advice: if your FPGA design targets a single host and demands the lowest latency, PCIe is the better path. For distributed systems where storage must span multiple devices, Fabrics like RoCE or TCP/IP deliver the necessary scalability, even with the added overhead.

PCIe switch architectures for multi-NVMe FPGA deployments

A PCIe switch in multi-NVMe FPGA setups routes memory requests by matching TLP addresses to downstream port apertures.

When an NVMe endpoint sends a memory request upstream, the switch checks the transaction-layer packet (TLP) address against each downstream port’s memory aperture. If the address falls within a port’s aperture, the switch forwards the TLP to that port, enabling direct endpoint-to-endpoint communication with predictable latency. This routing mechanism requires the FPGA designer to align memory mappings with the switch’s aperture registers during initialization, as misalignment can lead to dropped or misrouted packets.

Access Control Services (ACS) introduce policy-based routing that can override aperture-based decisions. When enabled, ACS may block a TLP as an error or redirect it upstream, even if the address matches a downstream aperture. While this feature supports centralized error handling or security filtering, it adds latency and complexity. For most multi-NVMe FPGA deployments, we recommend disabling ACS redirection unless explicit security or error-handling requirements justify the overhead.

Plan your topology carefully.

In systems where multiple NVMe endpoints share a PCIe switch, the designer must balance aperture sizes, endpoint memory requirements, and ACS policies to avoid conflicts. A poorly configured switch can create bottlenecks, particularly when ACS redirection forces traffic upstream unnecessarily. For example, if two endpoints frequently communicate, their memory apertures should be sized to minimize overlap with other endpoints, reducing the likelihood of ACS intervention. Test aperture mappings in simulation before hardware deployment to catch misalignments early.

Compliance testing requirements for NVMe IP on FPGA

NVMe IP on FPGA doesn’t require mandatory certification, but UNH-IOL compliance testing helps verify interoperability.

NVM Express collaborates with the University of New Hampshire InterOperability Laboratory (UNH-IOL) to conduct compliance and interoperability testing for NVMe, NVMe-oF, and NVMe-MI specifications as outlined by NVM Express. While this testing isn’t a formal certification requirement for FPGA-based NVMe host IP, it provides a standardized way to verify compatibility with industry implementations. The UNH-IOL NVMe plugfest events allow companies to test their technology in real time alongside other industry participants per NVM Express.

For FPGA deployments, this testing is especially useful when integrating NVMe IP cores with third-party storage devices or host systems. The absence of mandatory certification doesn’t eliminate the need for validation: particularly in environments where interoperability is critical, such as data centers or embedded storage solutions. The plugfest model helps engineers identify protocol mismatches or performance bottlenecks before deployment, reducing integration risks in multi-vendor ecosystems.

We recommend prioritizing compliance testing for FPGA-based NVMe IP when targeting deployments with mixed hardware vendors. This step reduces integration risk without requiring formal certification.

Our FPGA IP portfolio includes NVMe host and SAN cores for Altera, AMD and Microchip devices, from PCIe Gen3 to Gen5, as listed in our product catalogue.

Latency and throughput benchmarks for FPGA-integrated NVMe IP

A peer-reviewed FPGA design, FastPath, reported up to 71% lower latency and up to five times higher I/O performance than its baseline.

University of Manchester researchers evaluated FastPath on a Zynq development board and presented it at FPL 2018. The evaluation reports up to 71% lower latency and up to five times higher I/O performance compared with the unmodified baseline system, measured on hardware.

These improvements matter most in latency-sensitive applications like real-time analytics or edge computing, where microsecond delays impact system performance. Higher throughput also enables faster data transfers, critical for workloads requiring sustained high bandwidth.

To leverage these gains, match your FPGA’s PCIe generation to your throughput needs. A Gen4 x4 interface carries about 7.9 GB/s per direction, and Gen5 x4 doubles that. The table below summarizes the theoretical bandwidth for each configuration:

PCIe Generation Lanes Bandwidth per direction after encoding (GB/s)
Gen3 x4 ~3.9
Gen4 x4 ~7.9
Gen5 x4 ~15.8

For engineers targeting these benchmarks, we recommend selecting FPGA families with native PCIe Gen4 or Gen5 support. Altera Agilex 7 devices with R-Tile, for example, offer PCIe hard IP up to Gen5 x16. Pairing these with an optimized NVMe IP core, like those listed in our catalogue, helps approach these figures; measure them with your own workload.

Test early with real workloads.

Constraints of NVMe IP integration on FPGA: power, thermal, and signal integrity

NVMe IP integration on FPGA at PCIe Gen5 speeds demands strict power, thermal, and signal integrity controls to avoid performance degradation.

Power delivery must remain stable at PCIe Gen5’s 32 GT/s transfer rates. High-speed transceivers need clean voltage rails, where even minor fluctuations can disrupt timing. We recommend isolating PCIe lanes on a dedicated power plane to minimize noise coupling from other logic blocks. Size the rails with the FPGA vendor’s power estimation tool and validate them on the board before enabling full-speed operation.

Thermal management becomes critical as power density increases. Transceivers running at 32 GT/s add to the device’s power budget, so plan the thermal solution from the vendor’s power estimate, not from the logic alone. Passive cooling may suffice for short bursts, but continuous 32 GT/s transfers demand airflow or a thermal interface material with low thermal resistance. Monitor die temperature during sustained transfer tests, not only at idle.

Signal integrity is highly sensitive to impedance mismatches at 32 GT/s. A 2026 study in Micromachines proposes an end-to-end method to simulate how the package degrades signal integrity in PCIe channels: the channel budget includes the package, not only the PCB. Use controlled-impedance traces and validate with time-domain reflectometry (TDR) measurements. For high-speed designs, prioritize short, direct routing and avoid sharp bends or vias near transceiver pins.

The table below summarizes what to check before layout sign-off:

Constraint What to check How
Power delivery Transceiver rail stability at full link load Vendor power estimator, board measurement
Thermal Die temperature under sustained transfers Heatsink or airflow sized from the power estimate
Signal integrity Impedance along the full channel, package included Controlled-impedance routing, TDR

The best choice here: estimate power and thermal margins with the vendor’s tools early, and validate signal integrity with TDR before finalizing the PCB layout.

In summary

Start by mapping your target throughput to the FPGA’s PCIe hard IP blocks. For Gen5, Agilex 7 devices with R-Tile provide a hardened PCIe 5.0 x16 interface; for Gen3 and Gen4, check which hard IP your target device offers and which interface width the NVMe host IP uses on it. Simulate aperture mappings for multi-NVMe switches to avoid misrouted TLPs, and disable ACS redirection unless security policies demand it. Test power rails and thermal margins at Gen5 speeds before deployment: minor fluctuations can disrupt timing. For interoperability, schedule UNH-IOL plugfest testing early, especially in multi-vendor environments.

How we wrote this article

The sources we consulted are listed at the end of the article, consulted on 1 October 2026. Where we cite none, it is our opinion, and we write it as such.

This article gives buying criteria and our point of view. It does not replace a professional’s advice on a specific situation.

It is published by Logic Design Solutions, which therefore has an interest in the subject.

Sources
  1. What’s The Difference Between SATA And NVMe? | Electronic Design, electronicdesign.com
  2. HighPoint adaptors boost PCIe slots for GPU scalability …, eenewseurope.com
  3. First 8-lane analyzer for PCIe 5.0 …, eenewseurope.com
  4. Introducing the PCI-SIG® 2020 Virtual Product Wall | PCI-SIG, pcisig.com
  5. Excelero extends NVMesh reach with TCP and Fibre Channel support, blocksandfiles.com
  6. Agilex 7 with R-Tile launched: integrated PCIe Gen5 and CXL, servethehome.com
  7. Testing & Compliance – NVM Express, nvmexpress.org
  8. FastPath: Towards Wire-speed NVMe SSDs – Research Explorer The University of Manchester, research.manchester.ac.uk
  9. An End-to-End Design and Simulation Methodology for Evaluating Package-Induced Signal Integrity Degradation in PCIe Chan, mdpi.com
  10. Products – Logic Design Solutions | Logic Design Solutions, logic-design-solutions.com